How To Replace CV Boots: (Applies to most Nissans except the Quest) The simple gist of it: Put the front end of the car up on jack stands. Remove the left front wheel. Remove the retainer pin for the center hub nut. Remove the center hub nut (BIG breaker bar and 32 or 36 mm […]
4th-Gen Maxima: Replacing Motor Mounts
How To change Motor Mounts: Here are the tools it takes to complete the job: 1) floor jack 2) two 17mm short sockets 3) ~2.5′ of 1/2″ extensions 4) 1/2″ rachet 5) 18″ 1/2″ breaker bar 6) jack stands 7) 10mm socket and 1/4″ ratchet 8) “Bottle” jack 9) torque wrench 10) penetrating oil (preferably […]
Nissan Maxima O2 Sensor Replacement
Replacing Maxima O2 Sensors Upstream O2 sensors: Necessary tools: *3/8″ drive ratchet *22mm O2 sensor removal ratchet (rent it from Autozone for free) *OEM upstream O2 sensor(s) *Anti-seize *PB Blaster (or WD40) *Scissors 1. Put the front end of the car on ramps or jackstands 2. Spray the O2 sensors with PB blaster (or other […]
4th-Gen Maxima Strut Boots Replacement
After doing some searching prior to doing my suspension install recently I found this information: “SB103 for the fronts and SB108 for the rears. Select the front boots for 95′ Mustang (SB103) and rear boots for 95′ Miata (SB108).” I thought that with all of the people looking to do suspension installs I would post […]
5th-Gen Maxima Coilover Installation
Special thanks for this write up goes to Fezzik (David Honey). Posted with permission from the author. Here is what the rear coilover that I tested looked like compared to the stock rear suspension. These are still being tested and are not offered yet. You will first want to measure the car’s wheel gap right […]
Turbocharging the B15 Sentra
Turbocharging the B15 Sentra (SR20DE+T) By: nametakennow There are a number of ways to go about this, including engine swaps, aftermarket kits, and piece-together rigs. I went with the last of that set. Before: After: One of the most infuriating portions of my turbo quest has been figuring out what parts I need/have. Thus, as […]
3rd-Gen Maxima water pump replacement
Water Pump Replacement This is a How To on how to replace the water pump in a 3rd generation Maxima with the VG30E engine. (89-94 GXE and 89-91 SE models only) The VE’s may be similar but I am not sure since I do not have one. Tools needed:jack STANDSjackstire removal toolsflathead screwdriver8, 10, 12, […]
Maxima short-throw shifter installation
Installation of Pacesetter Short Throw Shifter in 3rd-Gen Maxima This is the how to for the Pacesetter Short Throw Shifter just incase you guys get one and happen to lose the paper or the paper doesn’t come with it. Quick Shift Kit Contents1 – Shifter lever1 – Delrin pivot ball2 – Bushings1- 1/4″ x 1/4″ […]
3rd-Gen Maxima Fuel Injector Replacement
Fuel Injector Replacement – 3rd Generation w/VE30DE Note that this information is related to the 92-94 VE30DE engine, although I’m sure some of it can be applied to the VG30E engine, as well. If you have any doubts on your capability in performing this replacement, take your car to a certified mechanic. What you need: […]
Q45 Heater Mix Door Removal / Replacement
By: Brian (bigdog76) http://forums.nicoclub.com/zerothread?id=156041 1.Fixing the Heater was not all fun I will admit. 2.However it is possible and it’s not to hard to do. It took me much longer than I wanted but can be done in 2-4 hours, for under $10 if you have the tools to do it. 3.First start by removing […]
- « Previous Page
- 1
- 2
- 3
- 4
- …
- 17
- Next Page »