Since there is no Infiniti dealer within driving range, I take my car to the local Nissan dealer for service. Despite having traded off my 350Z nearly a year ago, I still get their “Nissan” mailings and the offer of a $19.95 oil change from them was irresistible, so down I went for a few […]
Nissan Maxima – Heated Side Mirror Installation
Special thanks for this write up goes to Fezzik (David Honey). Posted with permission from the author. This is the How To on the installation of heated mirrors. A few things first before I go on. I have the automatic climate control with the rear window defogger switch on it. The side view mirrors are […]
Maxima Rear Sway Bar Install
The following directions can be utilized in the installation of an Addco RSB onto a 5th Generation (2000-2003) Maxima. Installation onto a 4th generation (1995-1999) should be similar. It is recommended that two people perform the installation, but, one person could accomplish the task. Please view pictures with steps for additional detailed information. Step 1. […]
5th/6th-Gen Maxima – How to Reset ECU
How to reset ECU in 5th and 6th Generation Maxima’s 1. Turn ignition switch on and wait about 3 seconds. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds. 2a. Fully depress the accelerator pedal (HARD).2b. Fully release the accelerator pedal. 3. Wait 7 seconds, fully depress the accelerator pedal […]
2002 Nissan Maxima Review – From an Owners Perspective
It was a cold and wet day in November, as I remember, when I drove my first Maxima. I had looked at a 2002 a few weeks before, while visiting the local Nissan dealership to see the new Altima.There was something about it, calling my name. But, I digress.On this day, I was required to […]
4th-Generation Maxima: How to Install a 2000 VI Manifold
This write up is for a 2000-01 VI manifold swap on to 95-99 Maxima. There are many ways to do this swap so first I will number the ways I know how to do this and then go into detail on how to do it. There are a couple of different Upper manifolds you can […]
3rd-Gen Maxima Turbocharging
How to Turbo a 3rd Gen Maxima I get a lot of emails from people asking me where to get a JDM engine but in my opinion, after having done the swap and such, that’s not the way to go. I think the best way to turbo you VG maxima would just be to use […]
LED Lighting Maxima Auto Gear Shifter
TOOLS NEEDED:Soldering ironRosen core6 White 3mm LEDS (preferred) or 5mm LEDS6 470 Ohms resistorsBreadboardDremel sand paperFlat head screwdriverHot glue gunHeat shrinkSnap or slide connectors First, remove the gear selector trim from the car. Remove the shifter trim, then remove the 4 screws holding the gear selector trim. Then remove the bulb socket. the gear trim […]
5th-Generation Maxima: Car Audio Wiring Codes
Article Series
The following information was researched via multiple Maxima FSM’s. ——————————————————————————– Base Headunit plug diagram ——————————————————————————– Bose Headunit plug diagram ——————————————————————————– Bose amp plug diagram ——————————————————————————– Speaker Wiring Chart (Both Bose and Non-Bose) Information provided by:audtatious
Removing and Installing the Rear O2 sensor on a Nissan Maxima/Infiniti I30
This describes the removal and installation of the rear O2 sensor behind the catalytic converter for 95-99(Federal Emissions) Maxima/I30s. Items Needed: PB Blaster (or other rust penetrant) 22mm Wrench Flat Head Screwdriver Electrical Tape Jack and Stands Work Light First you will need to remove the bad O2 sensor. Use generous amounts (frequently) of the […]
- 1
- 2
- 3
- …
- 5
- Next Page »