Thought I’d pass on a write up I did tonight on my G37 vert 6mt. I did this mod on my Maxima as soon as I got it. the clutch engagement is way too high. So I lowered it on my max. I drove 70k miles like that on the stock clutch and it was […]
Connect your iPod (or other MP3 player) to the Factory Audio System
Applied Vehicle(s): Infiniti QX4 Difficulty Rating: Estimated Labor Time: 1½ hours Written By: rwardell Estimated Total Cost: $20.00 Find related tutorials and information on your vehicle in NICOclub’s Nissan Forums & Infiniti Forums This is a cheap and easy way to connect a 3.5mm standard head phone jack to the factory Bose head unit in […]
Remove and Install Lug Studs
Applied Vehicle(s): All Nissan/Infiniti vehicles Difficulty Rating: Estimated Labor Time: 1 hour Written By: bllabong89 Estimated Total Cost: $15.00 Find related tutorials and information on your vehicle in NICOclub’s Nissan Forums & Infiniti Forums So I just put my extended lug studs in and I just wanted to make a How To article so people […]
Nissan Cube Stillen intake and exhaust installation
“Operation Dropbox” – Installing a Stillen Intake and axle-back exhaust on NICO’s Nissan CubeCubeDriver.com started modifying Project Cube almost before the ink was dry on the contract.With a lowered stance, and upgraded wheels and tires, it was time to turn our thoughts towards a little performance increase.While the Cube is no stoplight warrior by any […]
4th-Generation Maxima: How to Install a 2000 VI Manifold
This write up is for a 2000-01 VI manifold swap on to 95-99 Maxima. There are many ways to do this swap so first I will number the ways I know how to do this and then go into detail on how to do it. There are a couple of different Upper manifolds you can […]
5th-Generation Maxima Injen Intake Installation
The following directions have been compiled to assist in the installation of an Injen intake onto a ’02-03 Maxima. The directions should also work with ’00-01 Maximas as well. Tools needed: 10mm socket + ratchet, ratchet extension, 10mm wrench, flat-head and phillips head screwdriver, Pliars ——————————————————————————– Parts: The injen intake should consist of the following […]
Cleaning Idle Air Control Valve
How To Clean IAC valve: Tools needed: – 10 and 12 mm sockets – 3 inch socket extension – universal joint (swivel pivot socket thing) – 12-inch ratchet (a short ratchet may not work – need something to apply a lot of torque to loosen the bolts) – Phillip’s screwdriver – rag – throttle body […]
Installing the VG30 in a Datsun 510
Installing the VG 30 in a 510 By Michael Spreadbury Thinking about an engine swap? Tired of seeing L16-18-20B’s every time that you open a 510 hood? Want to have a reliable, powerful 510? Consider the VG30, Nissan’s 3.0 liter V6 engine. There have been many requests for an article about installing the Nissan VG30 […]
Nissan Frontier Garmin GPS Installation
taken from dumbengineer.com Removed 8 case screws, opened unit (clamshell), and mounted on plexiglass using original screws. Using elastic, and holes in the plexiglass, mounted unit to visor so that I can see it with my visor down. Using custom built blocks of wood, I lowered the visor by about an inch so the GPS […]
5th-Generation Maxima Y-pipe and Cat installation
Maxima Y-pipe and cat installation By: beancooker 1. Remove all heat shields (10mm wrench). 2. Remove O2 sensors. 3.Spray penetrating oil on all bolts to be taken out. YOU WILL NEED A PIVOTING ADAPTER FOR YOUR SOCKET WRENCH. Remove 3 bolts on front bank, 3 bolts on rear bank and 2 bolts on cat. 14mm […]