Applied Vehicle(s): Infiniti G35, Infiniti G37 Difficulty Rating: Estimated Labor Time: 1½ hours Written By: G35MoonRiver Estimated Total Cost: $220.00 Find related tutorials and information on your vehicle in NICOclub’s Nissan Forums & Infiniti Forums The rear view on my 2007 Infiniti G35 Coupe is extremely limited that every time I backup it makes me […]
OEM or Aftermarket Brake Installation Q45 J30
Infiniti Q45 & Infiniti J30 TOOLS: jack and jack stands 1/2″ ratchat 13/16 socket 19mm socket 17mm socket 14mm socket 12mm socket 10mm wrench 4″ angle grinder COST BREAKDOWN: $44 used Q45 calipers, pads, and rotors (I used a digital caliper and measured the rotors and pad so i knew i was getting good ones) […]
Installing a KA24 into a Datsun 510
– Nissan KA24 install article. By Danny Youngs Nissans KA24 motor can be installed into the Datsun 510 in many different ways and forms. In this article I will cover every facet of installation and the different parts you can use to do this. I studied many different ways of doing the install before I […]
Removing and Installing the Rear O2 sensor on a Nissan Maxima/Infiniti I30
This describes the removal and installation of the rear O2 sensor behind the catalytic converter for 95-99(Federal Emissions) Maxima/I30s. Items Needed: PB Blaster (or other rust penetrant) 22mm Wrench Flat Head Screwdriver Electrical Tape Jack and Stands Work Light First you will need to remove the bad O2 sensor. Use generous amounts (frequently) of the […]
Nissan Frontier Drawtite Hitch Install
from Nissan Offroad Installers Notes This installation was performed by a certified mechanic and the owner of the vehicle pictured. At no point do we recommend altering or otherwise changing the geometry of the rear bumper system. If you feel you are unable to safely install this piece of equipment, please see a certified Vehicle […]
Installing a PCV Blow-by Oil Catch on a Nissan Maxima/Infiniti I30
Credit to Beancooker for the writeup. I TAKE NO RESPONSIBILITY IF YOU MESS UP YOUR CAR!!! PROCEED AT YOUR OWN RISK!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! O.k. this is a really easy mod, it won’t give you horsepower, per se, but keeps you from burning any blow-by oil and dirtying your intake manifold. Also adding oil to gas lowers octane […]
Nissan Maxima: LED interior lighting
Cost -$40. You will need: assorted screwdrivers pliers wire LED’s with resistors for 12v a drill with bit the size of your LED patience time electrical tape soldering iron optional (recommended) i think that’s it PUTTING LED’s IN YOUR DOOR LIGHT 1. Disconnect fuse for door lights if you desire. 2. Pry off clear cover […]
Nissan Altima K&N Intake Install Guide for 2.5
This tutorial will guide you on how to install a K&N intake on a 2.5 Nissan Altima Supplies needed: K&N intake “kit” 8mm and 10mm sockets ratchet and extension philips and flathead screwdrivers 3mm and 5mm allen key wrenches pliers rags (box of rags works wonders) Steps: 1) Turn off the ignition and disconnect the […]
Installing a SPC Rear Camber Kit and Toe Bolts on an Inifiniti G35
This article will show you how to install a SPC rear camber kit and make modifications for Toe bolts. TOE BOLTS: Tools used: 19mm socket 17mm socket breaker bar 2 socket wrenches sharpie Dremel #115 dremel bit Jack & Jack Stands Jack the car up and place jack stands. Loosen stock toe bolt. Using hydraulic […]
Nissan Altima DIY Big Brake Kit
This is an install tutorial that will help you to replace both front and rear rotors and calipers, brake pads, and brake lines. So, Let’s get to it. You’ll need to jack your car up and place stands underneath the recommended areas first. For this tutorial, the car was brought to a garage with a […]