This article is to assist you in changing the air filter in a VQ35HR. Yesterday I decided to change the air filters on the Z. I had a spare hour till the GF came down so I figured this would be something I could do that would take an hour. As it turns out, I […]
Installing an Under Drive Lightweight Pulley on an Infiniti G35
This article will guide you in how to install a under drive lightweight pulley. Tools needed: 3/8″ Socket Wrench with 14mm & 12mm sockets 1/2″ Socket Wrench with 19mm deep socket Floor Jack/Jack Stands Jack your car up. Use jack stand for safety. I only raised the passenger side of my car and it was […]
Nissan Altima DIY Big Brake Kit
This is an install tutorial that will help you to replace both front and rear rotors and calipers, brake pads, and brake lines. So, Let’s get to it. You’ll need to jack your car up and place stands underneath the recommended areas first. For this tutorial, the car was brought to a garage with a […]
Nissan Altima DIY Dry Filter Cleaning
This article will help you on how to clean a dry air filter normally found with Fujita Air Intakes Notes: – There are two types of after market Cone filters, Wet and Dry. This write-up is for Dry type filters. Wet type filter require re-oiling. Check with you filter manufacturer for details. – This should […]
Infiniti G35 Clutch Replacement
How to replace a clutch in a 03-07 Infiniti 6 speed. Now as a word of precaution I must start by saying this is not something I would recommend doing in your driveway as the transmission is not only pretty heavy but there are bolts that need to accessed on the top of the bell […]
Nissan Altima 3.5 DIY Oil Change Procedure
This tutorial will help guide you to change your oil on a 3.5 Altima.You will need the following items to accomplish this task: 5 quarts of oil 1 oil filter 1 new washer 2 floor jacks and/or ramps 14mm socket Oil filter wrench Oil drip tray Rags Funnel Step 1:Line your car up and drive […]
Nissan Altima K&N Intake Install Guide for 2.5
This tutorial will guide you on how to install a K&N intake on a 2.5 Nissan Altima Supplies needed: K&N intake “kit” 8mm and 10mm sockets ratchet and extension philips and flathead screwdrivers 3mm and 5mm allen key wrenches pliers rags (box of rags works wonders) Steps: 1) Turn off the ignition and disconnect the […]
Nissan Altima DIY License Plate Bumper Plugs
This tutorial will show you how to make a DIY License Plate Bumper Plugs which are readily available at any Lowes or hardware store. You will need the following items: Hillman Push Fasteners “Nissan” #881204 or #881206 X-Acto Knife Touch Up Paint Clear Coat Sandpaper Procedure: 1. You can get these fasteners at Lowe’s. I […]
Nissan Altima How To Replace Front & Rear Rotors
In this tutorial, we will show you how to replace your OEM rotors with aftermarket Stillen rotors on a Nissan Altima. It is a very easy procedure and requires the following: Difficulty: Easy Tools: Jack & stand, 19mm wrench (not socket/ratchet) Time: Roughly 20 minutes per rotor Front: Comparison Step 1: Starting at the front, […]
Installing an Under Drive Pulley for the Infiniti VQ35DE
This instruction is specific to the VQ35 DE motor. Is to help guide you in the removal of the OEM pulley and installation of an aftermarket Under Drive Pulley. First jack up the car, (in my case, the lift) and remove the wheel and access cover which is held on with 5 clips. Here’s a […]
- « Previous Page
- 1
- …
- 94
- 95
- 96
- 97
- 98
- …
- 152
- Next Page »