This article written by: Toby Broadfield This article will show step-by-step process of building fiberglass molded panels from the skeletal beginnings, to the final painted product. Keep in mind that a painted product is not always the route taken. Some customers want it vinyl wrapped, carpeted or wrapped in something else…. carbon, Kevlar etc. Using […]
Nissan Altima: Install the Stillen Front Strut Tower Bars
So my new Stillen Strut tower brace came in and I was excited as hell to install it. At first I wasn’t going to do a full write up on it since Stillen’s instructions are pretty clear but also includes the the instructions to install it on the 09 Maxima but I know that there […]
DIY guide to lowering a Nissan/Datsun pickup truck
Many people tend to be curious as to the lowering of their pickups when they get them. This is the simple process to lower a Nissan or Datsun truck. It covers models all the way from back in the Datsun days through the hardbody days. The process uses lowering blocks in the rear and adjusting […]
Z32: DIY JDM Taillights
How to convert your 300zx (Z32) USDM taillights to JDM taillights This isn’t meant to be a “How-to” write up. But you can follow it at your own discretion as you may break your tails. I did, but I had a back-up set. Tools Needed: Paint Brush Oven or heat gun Terry or microfiber cloth […]
Refinishing the Headlights on an Infiniti I30/Nissan Maxima
How to refinish your headlight to make them look brand new. This DIY article will show you how to remove the haze from your I30/Maxima headlights. Tools/Materials Needed: Wet/dry sandpaper in 1000, 1200, 1500, and 2000 grit Car polish (not wax, but a fine cut polish) Soft cloth or those blue autozone paper towels Spray […]
Installing a SPC Rear Camber Kit and Toe Bolts on an Inifiniti G35
This article will show you how to install a SPC rear camber kit and make modifications for Toe bolts. TOE BOLTS: Tools used: 19mm socket 17mm socket breaker bar 2 socket wrenches sharpie Dremel #115 dremel bit Jack & Jack Stands Jack the car up and place jack stands. Loosen stock toe bolt. Using hydraulic […]
How to rebuild your starter
In this article we will be rebuilding a starter for an SR. This can be a relatively straightforward and relatively inexpensive repair, if you have the time and patience. Skill Level 4 of 5 Time Required 25mins – 2hours.(the first time it takes longer) (not including R&I) Tools and Equipment -8mm, 10mm, 12mm socket -Flathead […]
Installing LED lights in an Altima Coupe
Alrighty, so here’s the how to, pretty straight forward, toughest part was getting the wire from the engine compartment to the driver’s panel. Prepping of car: I will skip the details in some of the easier steps, such as -take off the front grill – all plastic clips, then pull straight out -take off the […]
Removing The DVD Player From An Infiniti QX56 Console
This article will show you how to remove the center console mounted DVD player. The DVD player may require replacement or repair and this walk through will help get it out. Skill Level 2 of 5 Time Required ~1hr Tools -Phillips Screwdriver -Small Flathead Screwdriver Procedure 1. 1. Remove instrument lower cover RH. There are […]
Altima Coupe: Installing LEDs In The Center Vent And Cupholders
My philosophy with any automotive accent lighting is that the lights themselves shouldn’t be seen…only their soft glow. As such, I try to make sure that I mount my LEDs in places where they will reflect off many surfaces and give the nicest ambient light. Skill Level 3 of 5 Time Required 1-1 1/2hrs. Tools […]
- « Previous Page
- 1
- …
- 95
- 96
- 97
- 98
- 99
- …
- 152
- Next Page »