Valve cover gasket replacement on Infiniti I30 and Nissan Maxima: As the VG30 gets older, and more of them get up there in mileage, a common problem has come to light. The valve covers and spark plug seals often leak oil. Both out onto the block, and into the spark plug tubes. This can diminish […]
3rd-Gen Maxima Turbocharging
How to Turbo a 3rd Gen Maxima I get a lot of emails from people asking me where to get a JDM engine but in my opinion, after having done the swap and such, that’s not the way to go. I think the best way to turbo you VG maxima would just be to use […]
3rd-Gen Maxima Fuel Injector Replacement
Fuel Injector Replacement – 3rd Generation w/VE30DE Note that this information is related to the 92-94 VE30DE engine, although I’m sure some of it can be applied to the VG30E engine, as well. If you have any doubts on your capability in performing this replacement, take your car to a certified mechanic. What you need: […]
Maxima short-throw shifter installation
Installation of Pacesetter Short Throw Shifter in 3rd-Gen Maxima This is the how to for the Pacesetter Short Throw Shifter just incase you guys get one and happen to lose the paper or the paper doesn’t come with it. Quick Shift Kit Contents1 – Shifter lever1 – Delrin pivot ball2 – Bushings1- 1/4″ x 1/4″ […]
3rd-Gen Maxima water pump replacement
Water Pump Replacement This is a How To on how to replace the water pump in a 3rd generation Maxima with the VG30E engine. (89-94 GXE and 89-91 SE models only) The VE’s may be similar but I am not sure since I do not have one. Tools needed:jack STANDSjackstire removal toolsflathead screwdriver8, 10, 12, […]
Maxima Rear Sway Bar Install
The following directions can be utilized in the installation of an Addco RSB onto a 5th Generation (2000-2003) Maxima. Installation onto a 4th generation (1995-1999) should be similar. It is recommended that two people perform the installation, but, one person could accomplish the task. Please view pictures with steps for additional detailed information. Step 1. […]
Removing and Installing the Rear O2 sensor on a Nissan Maxima/Infiniti I30
This describes the removal and installation of the rear O2 sensor behind the catalytic converter for 95-99(Federal Emissions) Maxima/I30s. Items Needed: PB Blaster (or other rust penetrant) 22mm Wrench Flat Head Screwdriver Electrical Tape Jack and Stands Work Light First you will need to remove the bad O2 sensor. Use generous amounts (frequently) of the […]
2002 Nissan Maxima Review – From an Owners Perspective
It was a cold and wet day in November, as I remember, when I drove my first Maxima. I had looked at a 2002 a few weeks before, while visiting the local Nissan dealership to see the new Altima.There was something about it, calling my name. But, I digress.On this day, I was required to […]
4th-Gen Maxima Knock Sensor Testing
Testing the Knock Sensor (KS): – The KS MUST be checked with a digital ohmmeter. Analog ohmmeters may cause damage to vehicle. 1) Raise the hood. View the engine from the driver’s fender. Look into the deep valley between the cylinder banks and below the intake manifold. Identify the KS as a black item fastened […]
Cleaning Idle Air Control Valve
How To Clean IAC valve: Tools needed: – 10 and 12 mm sockets – 3 inch socket extension – universal joint (swivel pivot socket thing) – 12-inch ratchet (a short ratchet may not work – need something to apply a lot of torque to loosen the bolts) – Phillip’s screwdriver – rag – throttle body […]
- « Previous Page
- 1
- …
- 3
- 4
- 5
- 6
- 7
- Next Page »