Fun with legal LSD First things first, what is a LSD? It stands for Limited Slip Differential. Why is this important? Because it allows your car to get an incredible holeshot due to increased traction. The differential is the thing in the rear of the car that splits the power coming from the driveshaft up […]
Z32: Shifter Removal
Time – 1-2 hours Tools Needed: – Phillips screw driver – 12mm socket – 12mm wrench – Medium extension – Tiny-*** hands (not required, but very helpful) Procedure 1. Remove the radio bezel by removing 4 phillips screws (red circles) that are hidden behind some clips. The bottom two in the following picture already have […]
Nissan Maxima 2002-2003 HID bulb replacement
The following directions can be utilized in the replacement of HID bulbs in the 2002-2003 Maxima. These instructions cannot be utilized with other years of the Nissan Maxima. One person can accomplish this task with no no problems. Please view pictures with steps for additional detailed information. Tools needed: 10mm deep socket or wrench The […]
Nissan Maxima: LED interior lighting
Cost -$40. You will need: assorted screwdrivers pliers wire LED’s with resistors for 12v a drill with bit the size of your LED patience time electrical tape soldering iron optional (recommended) i think that’s it PUTTING LED’s IN YOUR DOOR LIGHT 1. Disconnect fuse for door lights if you desire. 2. Pry off clear cover […]
Z32: Fuel Controller/Computer replacement
Since searching around on the internet revealed this is becoming a more common problem as the 300zx ages, I figured I’d address it. If you have the symptom that you turn your key off and remove it and your Z won’t shut off, it is most likely your fuel controller. Removal and replacement is simple […]
5th-Generation Maxima Y-pipe and Cat installation
Maxima Y-pipe and cat installation By: beancooker 1. Remove all heat shields (10mm wrench). 2. Remove O2 sensors. 3.Spray penetrating oil on all bolts to be taken out. YOU WILL NEED A PIVOTING ADAPTER FOR YOUR SOCKET WRENCH. Remove 3 bolts on front bank, 3 bolts on rear bank and 2 bolts on cat. 14mm […]
Make Your Own Motor Mounts
1991-1994 Nissan 240sx Overview: Ever since I finished my KA-T project, I’ve had an issue with hood fitment. Basically, the turbo manifold left the turbo too high, and the intake manifold left the throttle body too high. NISMO motor mounts only exacerbated the problem, leaving me with no clearance between the hood and engine. I […]
Complete Nissan Speaker Sizing Guide
NISSAN SPEAKER SIZE LIST (alphabetical) You can find good deals on car speakers at Amazon. By: Simmsled 200SX 1984-1998 2 Door 6.5 F. Door 6.5 R. Deck 1984-1988 Hardbody 6.5 F. Door 6.5 R. Side 240SX 1989-1993 2 Door 4×6 F. Door 6.5 R. Deck 1989-1993 Hardbody 4×6 F. Door 4×6 R. Side 1994-1998 2 […]
Complete Infiniti Speaker Sizing Guide
INFINITI SPEAKER SIZES By: Simmsled FX35/ FX45- 2004+ Dash – Left, Center, and Right 2.5 tweeters (one in each location) F. Door 6.5 R. Door 6.5 D-Pillars 2.5 tweeters Under Cargo Floor – 5.25 woofers (1 pair) G20 – 1991-1996 4 Door 4×6 F. Door 6.5 R. Deck I30 -1995-1996 4 Door 6.5 F. Door […]
Removing and Installing the Rear O2 sensor on a Nissan Maxima/Infiniti I30
This describes the removal and installation of the rear O2 sensor behind the catalytic converter for 95-99(Federal Emissions) Maxima/I30s. Items Needed: PB Blaster (or other rust penetrant) 22mm Wrench Flat Head Screwdriver Electrical Tape Jack and Stands Work Light First you will need to remove the bad O2 sensor. Use generous amounts (frequently) of the […]
- « Previous Page
- 1
- …
- 6
- 7
- 8
- 9
- 10
- Next Page »