Cost -$40. You will need: assorted screwdrivers pliers wire LED’s with resistors for 12v a drill with bit the size of your LED patience time electrical tape soldering iron optional (recommended) i think that’s it PUTTING LED’s IN YOUR DOOR LIGHT 1. Disconnect fuse for door lights if you desire. 2. Pry off clear cover […]
Installing a PCV Blow-by Oil Catch on a Nissan Maxima/Infiniti I30
Credit to Beancooker for the writeup. I TAKE NO RESPONSIBILITY IF YOU MESS UP YOUR CAR!!! PROCEED AT YOUR OWN RISK!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! O.k. this is a really easy mod, it won’t give you horsepower, per se, but keeps you from burning any blow-by oil and dirtying your intake manifold. Also adding oil to gas lowers octane […]
Nissan Altima DIY Big Brake Kit
This is an install tutorial that will help you to replace both front and rear rotors and calipers, brake pads, and brake lines. So, Let’s get to it. You’ll need to jack your car up and place stands underneath the recommended areas first. For this tutorial, the car was brought to a garage with a […]
Installing a KA24 into a Datsun 510
– Nissan KA24 install article. By Danny Youngs Nissans KA24 motor can be installed into the Datsun 510 in many different ways and forms. In this article I will cover every facet of installation and the different parts you can use to do this. I studied many different ways of doing the install before I […]
Nissan Frontier Drawtite Hitch Install
from Nissan Offroad Installers Notes This installation was performed by a certified mechanic and the owner of the vehicle pictured. At no point do we recommend altering or otherwise changing the geometry of the rear bumper system. If you feel you are unable to safely install this piece of equipment, please see a certified Vehicle […]
240SX How To: Remove / Replace your power steering pump
*place the pan underneat the driver’s side wheel/where the PS pump sits.*
***remove intake assembly, undo all spark plug wires, and remove all harness out of harm’s (ps fluid’s) way.
Removing the emissions box, oil dipstick and the ex. mani heat shield gives you A LOT more room to work with!***
1) Using the 15/16 or 26mm wrench, unbolt the main nut connected to the PS pump.
*unless you are re-doing the PS High Pressure Hose, like I did, no need to unbolt it at the banjo fitting. I used a home-made straight stainless-steel-braided line from the pump back to the hardline leading to the PS Rack.)
Installing SPL Coilovers on S14
Applied Vehicle(s): Nissan 240SX Difficulty Rating: Estimated Labor Time: 4 hours Written By: Unknown Estimated Total Cost: $750.00 – $3000.00 Find related tutorials and information on your vehicle in NICOclub’s Nissan Forums & Infiniti Forums Overview: Coilovers allow the ultimate in adjustable suspension performance for your car, and they are easier to install than a […]
S13 Low-Budget Front Lip
I know this is an old trick but I was so proud of my $15 lip I just had to post it! I put it on the other day and I think it looks pretty good.
Its no PDM lip but it also doesnt make me cringe every time enter a high angle driveway or hit a dip in the freeway at 80 mph.
I paid $10 for a whole 20ft roll (comes in a box) of baseboard molding in the “office supplies dept” of Home Depot.
Then $5 for a box of the wide head autobody screws from AutoZone. The wide head screws dont leave the dimple effect if you refrain from over tightening.
240sx2nr95’s Kouki S14 Sideskirts Installation
First off, if you haven’t done so, clean off all the old adhesive.
Next, sand down and paint your sideskirts, or have them painted.
If they’re already your color, perfect move on to the next step!
After sanding, I used a high quality exterior enamel satin black paint to paint the sideskirts, my mudflaps and my lip.Resists rock chips and well and holds up nicely to the elements (going on 3 years on the lip without needing a repaint.)
How to: S14 Subframe Removal
1995-1998 Nissan 240sx N/A 1-3 Hours NICOclub Rating System bllabong89 Before we start, I just want to say this is to remove the subframe if you already have the rear suspension/hub assembly removed. Also, If I have missed anything and/or have something incorrect, please give your input. This is here to help people who may […]
