Testing the Knock Sensor (KS): – The KS MUST be checked with a digital ohmmeter. Analog ohmmeters may cause damage to vehicle. 1) Raise the hood. View the engine from the driver’s fender. Look into the deep valley between the cylinder banks and below the intake manifold. Identify the KS as a black item fastened […]
Cleaning Idle Air Control Valve
How To Clean IAC valve: Tools needed: – 10 and 12 mm sockets – 3 inch socket extension – universal joint (swivel pivot socket thing) – 12-inch ratchet (a short ratchet may not work – need something to apply a lot of torque to loosen the bolts) – Phillip’s screwdriver – rag – throttle body […]
Nissan CV Boot Replacement
How To Replace CV Boots: (Applies to most Nissans except the Quest) The simple gist of it: Put the front end of the car up on jack stands. Remove the left front wheel. Remove the retainer pin for the center hub nut. Remove the center hub nut (BIG breaker bar and 32 or 36 mm […]
Technical Articles: 4th-Gen Maxima:Car Audio Wiring Codes
Article Series
The following information was researched via multiple Maxima FSM’s.For the 4th-gen Maxima, there were numerous options for the stereos, so make sure you are looking at the correct one. ——————————————————————————– Wire Color Chart ——————————————————————————– 1995 – 1999 diagram for 4-speaker systems ——————————————————————————– 1995 Bose diagram ——————————————————————————– 1996 – 1999 Bose diagram ——————————————————————————– 1996 Non-Bose 6 […]
5th-Generation Maxima: Car Audio Wiring Codes
Article Series
The following information was researched via multiple Maxima FSM’s. ——————————————————————————– Base Headunit plug diagram ——————————————————————————– Bose Headunit plug diagram ——————————————————————————– Bose amp plug diagram ——————————————————————————– Speaker Wiring Chart (Both Bose and Non-Bose) Information provided by:audtatious
5th-Generation Maxima Injen Intake Installation
The following directions have been compiled to assist in the installation of an Injen intake onto a ’02-03 Maxima. The directions should also work with ’00-01 Maximas as well. Tools needed: 10mm socket + ratchet, ratchet extension, 10mm wrench, flat-head and phillips head screwdriver, Pliars ——————————————————————————– Parts: The injen intake should consist of the following […]
Maxima Rear Sway Bar Install
The following directions can be utilized in the installation of an Addco RSB onto a 5th Generation (2000-2003) Maxima. Installation onto a 4th generation (1995-1999) should be similar. It is recommended that two people perform the installation, but, one person could accomplish the task. Please view pictures with steps for additional detailed information. Step 1. […]
4th-Generation Maxima: How to Install a 2000 VI Manifold
This write up is for a 2000-01 VI manifold swap on to 95-99 Maxima. There are many ways to do this swap so first I will number the ways I know how to do this and then go into detail on how to do it. There are a couple of different Upper manifolds you can […]
4th-Generation Maxima – White Gauge Faces
There have been lots of questions lately about this mod, so here are the facts as they pertain to 95-97. I am sure that they are the same for the 98-99.5, but my actual swap was in a 96. Also, these will work with an I30 or I30t, so long as you use a donor […]
4th-Gen Maxima Strut Boots Replacement
After doing some searching prior to doing my suspension install recently I found this information: “SB103 for the fronts and SB108 for the rears. Select the front boots for 95′ Mustang (SB103) and rear boots for 95′ Miata (SB108).” I thought that with all of the people looking to do suspension installs I would post […]
- « Previous Page
- 1
- …
- 48
- 49
- 50
- 51
- 52
- …
- 54
- Next Page »