This article shows you how to read/pull the fault codes, usually accompanied by a Check Engine Light or Service Engine Soon, on your Altima with push button start. You do not need an OBDII code reader or any other special tools to do this. To take a reading without using an OBD II reader, you […]
Altima Instrument Gauge Lighting Change
First, I separated the the three pieces. They are easy to disassemble. Nothing but clips holding it together. Next, I separated the Bezel that has the notches for the speed, rpm, ect. I didn’t take off the needles because, I have had a bad experiences with that before. So, I peeled back the gauges and […]
Altima Coupe: Installing LEDs In The Center Vent And Cupholders
My philosophy with any automotive accent lighting is that the lights themselves shouldn’t be seen…only their soft glow. As such, I try to make sure that I mount my LEDs in places where they will reflect off many surfaces and give the nicest ambient light. Skill Level 3 of 5 Time Required 1-1 1/2hrs. Tools […]
Nissan Altima 3.5 DIY Oil Change Procedure
This tutorial will help guide you to change your oil on a 3.5 Altima.You will need the following items to accomplish this task: 5 quarts of oil 1 oil filter 1 new washer 2 floor jacks and/or ramps 14mm socket Oil filter wrench Oil drip tray Rags Funnel Step 1:Line your car up and drive […]
Nissan Altima DIY License Plate Bumper Plugs
This tutorial will show you how to make a DIY License Plate Bumper Plugs which are readily available at any Lowes or hardware store. You will need the following items: Hillman Push Fasteners “Nissan” #881204 or #881206 X-Acto Knife Touch Up Paint Clear Coat Sandpaper Procedure: 1. You can get these fasteners at Lowe’s. I […]
Nissan Altima How To Replace Front & Rear Rotors
In this tutorial, we will show you how to replace your OEM rotors with aftermarket Stillen rotors on a Nissan Altima. It is a very easy procedure and requires the following: Difficulty: Easy Tools: Jack & stand, 19mm wrench (not socket/ratchet) Time: Roughly 20 minutes per rotor Front: Comparison Step 1: Starting at the front, […]
Nissan Altima DIY Big Brake Kit
This is an install tutorial that will help you to replace both front and rear rotors and calipers, brake pads, and brake lines. So, Let’s get to it. You’ll need to jack your car up and place stands underneath the recommended areas first. For this tutorial, the car was brought to a garage with a […]
Nissan Altima DIY Dry Filter Cleaning
This article will help you on how to clean a dry air filter normally found with Fujita Air Intakes Notes: – There are two types of after market Cone filters, Wet and Dry. This write-up is for Dry type filters. Wet type filter require re-oiling. Check with you filter manufacturer for details. – This should […]
Altima AVIC F90BT and XM HD Tuner Install Microphone replacment
Overview: This DIY shows how to install a AVIC-F90BT, XM/HD tuner and Stock Microphone replacement Difficulty: 3 (Basic knowledge of automotive electrical wiring is needed) Time: 2 hours Cost:$500 – $1K (depending where you buy you’re supply) Materials: AVIC-F90BT, wire kit, Satellite radio kit Tools: wire stripper, electrical tape, solderless terminals, ohm/volt meter, Uni-bit/Step-bit or […]
Installing an Infiniti G35 Style Spoiler w/ Brake Light on an Altima Coupe
Overview: This DIY is to help install a G35 style Spoiler with brake light on the Altima Coupe Difficulty: 3 Time: 1 – 2.5 hours hours depending on skill level and how carefully everything is done People: possible with one, easier with 2 (for holding purposes and lining it up (second opinion)) Cost: To get […]