First, you have to determine if you have the gap needed for the lights. If you have the Stillen fascia, you’ll have the gap needed. Not sure on the stock so you’ll need to look and measure the distance. You’ll need about 1/4″ inches to fit the LEDs. Next, you’ll need 2 – 19″ white […]
Altima Coupe Redline Manual Trans fluid tutorial
First of all, this is for everyone that experiences clunky shifting, hard to go in a lower gear, abrupt gear matching, or that just wants smoother shifting. What you have to do if you want to really get rid of those problems is change the MANUAL TRANSMISSION FLUID to a synthetic one. Wait until you […]
Altima Coupe Racingline Rear Endlinks Install
You need– TWO 2-ton jackstands– ONE jack from the trunk– ONE ratchet with a 17mm socket– ONE 17mm wrench– ONE 19mm wrench OR locking pliers (I used the locking pliers) first you are going to need to jack the car up. Jacking points: You take your cheapo jack from the trunk of the car underneath […]
Altima Coupe Eibach Prokit Spring Install
Props: To Guitarist982 for knocking this out with me, taking notes, pictures, and throwing his weight behind the effort when brute force was necessary. Notes: These instructions are for the Altima Coupe 3.5. Although the variations between the 3.5 and the 2.5 are minimal, these instructions may not be entirely accurate for the 2.5. Guitarist […]
Altima 3.5 Injen Short Ram Intake Install
Okay, first off, I’d like to say that the installation is quite simple and straight forward. If you have basic mechanical skills, it shouldn’t take more than 40-45 minutes tops. I have a lot of experience with installing intakes, exhausts, headers, etc., and it only took me 35 minutes, but that’s because I took pics […]
Nissan Altima Aftermarket HID Installation without Bumper Removal
First, always disconnect the negative terminal of the battery when working with power Remove wheels. Always chock your back tires for safety. Underneath the bumper, there are 3 screws on each side which need to be removed. Not the clips, just the screws. Inside the well, you’ll find about 8-9 clips that have […]
Altima Coupe Smoked Taillight Overlay Install
Click Here for a How-To on removing your taillights– Clean the taillight you will be working on before proceeding – Using a bottle of a soapy water solution, spray the taillight down. Do the same for the vinyl overlay once you have peeled it from the backing. This ensures a slippery surface so you have […]
Altima Coupe Bumper Removal
Altima Coupe Bumper Removal This is used for reference on installing an aftermarket HID kit on your Altima Coupe. This step is needed for the installation Step One: Gather your tools. You will need a Phillips and a small flat-head screwdriver. Step Two: Open Hood. There will be 8 clips on the top of the […]
Do It Yourself Bumper Removal – Nissan Altima
Overview: This DIY is to help you remove the front bumper of any 1st generation Nissan Altima. Difficulty:1 Time:30 minutes Cost: $0.00 Materials: none Tools: 10MM socket / Ratchet w/ extension, Flat head screwdriver, Philips screwdriver Procedure: 1. You’ll need to get to some screws and bolts under your car so you might want to […]
General Altima OEM to LED Bulb Replacement
General Altima OEM to LED Bulb Replacement Overview: This article is to help you install LED in place of the OEM incandescent bulbs.So since nobody’s ever made a write up, and there seems to be a question about it every week, i figured i’d do a write up for everyone. Difficulty: 2 Time: 1 – […]
- « Previous Page
- 1
- …
- 3
- 4
- 5
- 6
- Next Page »